RULES

1. Turn marshals may not work on or repair cars. Turn marshal may pass a car to the designated work area for repair. If a pit lane is available all cars must enter and exit the racing surface via the pit lane at all times. Cars may rejoin the race after a repair is made. Any cars damaged and placed in the infield will remain there until that race is over.

2. All drivers must turn marshal the race immediately following their race.

3. Race directors will have ultimate authority over rules enforcement. The primary basis for any rules decision must be based on what will be best for the majority of racers. If an item is not addressed in the rules listed here than you should assume it is not legal.

4. No cussing, yelling or general disrespect for officials or other competitors will be tolerated! This is a HOBBY not a sport, we expect everyone to do their best to have a good time and not mess it up for everyone else.

INDOOR RACES

GENERAL

1. Race duration: Heat races 3 minutes, Semi features 5 minutes, Main feature 7 minutes.

2. Each car will run 3 heat races. The first heat is lined-up by draw, second and third by inverted finishing order from the previous race.

3. Points from all three heats combined will determine the feature race line-ups. One point for each finishing position (1st = 1point, 2nd = 2points etc...). Six cars will transfer to the A main, other cars will run a semi feature. Four cars will transfer from the semi to the main for a total of ten cars in the main event.

INDOOR OVAL CLASSES

LOSI 1/18 MINI LATEMODEL

1. This is a stock class racer.

2. Only NiMh batteries with a max 1600mah may be used.

3. Any transmitter that will work with the stock receiver is OK.

4. Aluminum front bulkhead brace (upper and lower) is OK

5. Shock oil may be changed to a different weight.

6. Battery may be moved to the left battery tray and electronics may be moved to center.

LOSI 1/18 MINI SLIDER

1. This is a open class.

2. The only parts that MUST remain stock are the tires and body.

3. No offset chassis.

OUTDOOR OVAL CLASSES

All height measurements are from bottom of chassis unless otherwise noted.

1/8 SCALE LATEMODEL

1. Any production based 1/8 scale offroad buggy/car chassis.

2. Tires: Ofna 86505, Losi , Sportwerks / Dynamite . There will not be any grooving of the tires. Does not have to be the pre-mounts, but must be that tire.

3. Must run a working diff in front and rear end of the car. May run a working diff or a spool for the center diff.

4. Can run up to a 3” Spoiler measured from the deck lid with 2” x 3” winglets, maximum of 3 across the rear spoiler.

5. Any NITRO engine.

6. Single speed transmission only.

7. Body: Losi, Ofna or A1 moulded 1/8 scale late model bodies only. Window openings may be cut out but all support pillars must remain intact. Body must fully cover the wheels.

SMALL BLOCK TRUCK 2WD

1. Truck, IMCA or EDM Body styles only. All bodies may have a 2” rear spoiler measured from the deck lid. The spoiler can be no wider than the bodies rear deck area. There is not be any side dams, but may run a sail panel that follows the roof line and must not be any taller than the roof. May not attach a sail panel to the body, it must be built in to it’s design.

2. Any small block engine up to .18 and all engines greater than .15 cu. In. must be of the RTR variety or electric motor with a maximum 7.4V battery.

3. All vehicles must run rubber truck tires and truck weels front and rear. 2.2 inch max rim size.

4. WHEEL BASE 10.75 - 12.5, MAX WIDTH -13.0 MIN WIDTH -11.0

5. 2wd rear wheel drive only. No multi geared transmission.

BIG BLOCK TRUCK 4WD

1. Any production based truck or truggy.

2. Body style optional. Buggy style rear wing OK, no side dams, spoilers or additional wings.

3. Street tires, or "crime fighter / bowtie" style treads only. NO big lug or "tractor" style tires.

4. Any NITRO engine or electric motor combination allowed.

5. 4wd only , multi gear transmission OK.

1/10 ELECTRIC SPRINT

1. Must have scale appearing cage, hood, side panels, nerf bars and bumpers. Minimum of a 4 post cage required that resembles a drivers cockpit. All electronics must be positioned inside the cage side frames. Rear cage side panels may be used but may not extend beyond rear cage frame. No lexan or any other material may be mounted to nerf bars, bumpers, cage, wing or any other part of the car that will trap, alter, or direct air flow for the purpose of gaining an aerodynamic advantage. Must have appropriate openings on both sides of cage in driver compartment, forward portion of side panels can be no taller than highest point of hood. Losi 1/10 Slider OK to run in stock chassis configuration.

2. Specifications:

Maximum Length: 18.000"
Maximum width of hood: 3.600"
Maximum cage width at driver halo, down tubes, and top frame rail: 3.600"
Minimum vertical gap from top of hood to front cage crossbar: .750"
Wing minimum height at leading edge: 5.000" from bottom of chassis
Wheelbase: 9.500” min, 11.000" max
Maximum width: 10.250" (rubber tires)
Max wheel diameter: 2.2” front and rear
Max wheel width: 1.750” rear, 1.000” front
Max tire width: 1.850” rear, 1.250” front

Wing center section: 7x7” + 1” spoiler
L.S.- 5"TALL X 8"LONG
R.S.- 3 3/4"TALL X 8" LONG
FRONT WING-CENTER -4 3/4W X 3 1/16 LONG MAX.
L.S.-3 1/16 X 1 1/2" W
R.S.-3 1/16 X 1 1/2" W

3. Center wing must be made from at least 3 separate pieces of polycarbonate or lexan material, no one piece wings. Aluminum center sections may be used as long as there are no sharp edges. Main and Front wings must be mounted so that they are centered on cage, no offset wings. Wing center sections must have all 4 corners set at 90 degree angles, no canted or angled panels. Wings must also be mounted level from side to side. Center section of wing may not extend beyond leading or trailing edge of side panels. Side panels must have braces that hold side panel rigid at 90deg. to center section during race conditions. Two braces are required from top of the center foil to the left sideboard and one brace is permitted below the center foil to the right side board. Braces can be a maximum of .750" wide and front edge of front brace must be no more than 1.5” back from side panel leading edge. Side Panels may have front, back, top and bottom turnouts of no more than .375" and are included in max dimension. Flat foil center sections will be allowed a .250” turndown at the leading edge.

4. Any Brushed or Brushless Motor.

5. Any Nimh or up to a 2 cell 7.4v lipo Battery.

6. Headers are preferred on both sides but not mandatory.

-end-